Certexams.com Updates CCNA Network Simulator with Designer

Certexams.com recently updated it's network simulator product, Network Simulator with Designer for CCNA to include more labs. As you might be knowing, CCNA exam objectives have been revised some time back, and the new exam number id 200-301 (retired: 200-125). The labs offered by the network simulator are given below:


  1. Entering user EXEC prompt on a Router and Exit
  2. Introduction to Basic User Interface
  3. Basic Show commands
  4. Routing IOS Fundamental Exercises
  5. Banner MOTD : Setting Message of the Day
  6. Setting Host Name
  7. Router Interface Configuration
  8. Setting Bandwidth on an Interface
  9. Setting Console Password
  10. Setting Telnet Password
  11. Setting Auxiliary Password to Router
  12. Implementing exec-timeout command
  13. Copy Running Configuration to Startup Configuration
  14. Router CDP Configuration
  15. Show CDP Configuration
  16. Show CDP neighbors
  17. Bringing up a Router Interface
  18. Set Keepalive Timers
  19. Set Hostname and MOTD Banner
  20. Console and Line Password
  21. Host Table
  22. Viewing ARP Entries
  23. Telnet
  24. TFTP
  25. Exercises on Routing Fundamentals
  26. Introduction to IP
  27. Configuring Static routes
  28. Implement and Verify Static Routes
  29. Configuring Default route
  30. Implement and Verify Default Routes
  31. Configuring Loopback Interface
  32. Connectivity Tests with Traceroute
  33. Configuring RIP
  34. Basic EIGRP Routing
  35. Exercises on RIP/EIGRP Routing Scenarios
  36. RIP Routing Configuration Scenario
  37. Viewing IP RIP Information
  38. Configuring RIPv2
  39. RIP2 Routes
  40. EIGRP Routing Configuration Scenario
  41. EIGRP Troubleshooting Lab Scenario
  42. EIGRP Show Commands
  43. Exercises on OSPF
  44. OSPF Configuration in Single Area
  45. OSPF Troubleshooting Lab Scenario-1
  46. OSPF Troubleshooting Lab Scenario-2
  47. OSPF Troubleshooting Lab Scenario- 3
  48. OSPF Routing Configuration Scenario
  49. Exercises on Access-Lists
  50. Creating a Standard Access List
  51. Applying an Access List to an Interface
  52. View Access List Entries
  53. Standard Access List Scenario Lab 1
  54. Standard Access List Scenario Lab 2
  55. Router Access List Configuration
  56. Configuring and Verifying Standard Access List
  57. Configuring and Verifying Extended Access List
  58. Configuring and Implementing Extended Access List
  59. Verifying Extended Access-Lists
  60. Named Access-Lists
  61. Exercises on Network Address Translation
  62. NAT Scenario 1
  63. NAT Scenario 2
  64. NAT Scenario 3
  65. Dynamic NAT Scenario-1
  66. NAT Troubleshooting Scenario-1
  67. NAT and PAT
  68. Exercises on HSRP
  69. To enable HSRP on a Router
  70. To disable HSRP on a Router
  71. Configuring HSRP Priority , Delay and Preempt
  72. Load Sharing with Multigroup HSRP (MHSRP)
  73. Exercises on VPN(Virtual Private Network)
  74. Configuring site-to-site IPSEC VPN tunnel between routers
  75. Configure and verify a site-to-site IPSEC VPN
  76. Exercises on DHCP
  77. Configuring cisco router as a DHCP Server
  78. DHCP client configuration
  79. Configuring two DHCP clients and DHCP verification commands
  80. Exercises on PPP and ISDN
  81. PPP Configuration
  82. Configuring ISDN using BRI
  83. Configuring ISDN using BRI-Routing
  84. Exercises on Frame-Relay
  85. Configuring Frame-Relay without sub-interfaces
  86. Configuring Frame-Relay with point-to-point sub-interfaces
  87. Frame-Relay with sub-interfaces-Routing
  88. Frame-Relay Show Commands
  89. Frame-Relay Full Mesh Topology
  90. Exercises on Ipv6
  91. Enabling IPv6 on a cisco router
  92. Enabling IPv6 on a cisco router interface
  93. Configuring IPv6 on a cisco router interface with IPv6 address in EUI format
  94. Configuring IPv6 on a cisco router interface with IPv6 address in general form
  95. Configuring loopback interface with IPv6 address
  96. Configuring IPv6 on two router interfaces connected directly and pinging the distant interface sing console
  97. Traceroute lab
  98. Exercises on IPv6 Routing Protocols
  99. Enabling RIPng on a cisco router interface
  100. Enabling RIPng on two routers and pinging between them
  101. Entering RIPng router configuration mode and setting global parameters on a cisco router
  102. Configuring EIGRPv6 on a router interface
  103. Configuring EIGRPv6 on two routers and pinging between them
  104. Enabling OSPF for IPv6 on a cisco router interface
  105. Configuring OSPF on two router interfaces
  106. General IPv6 configuration on 2621XM series router
  107. Exercises on BGP
  108. Basic BGP Configuration
  109. Setting BGP attributes
  110. Setting the BGP neighbor password
  111. To disable the peer
  112. Basic Configuration of a Peer Group
  113. Configuring Multi Exit Discriminator Metric
  114. Exercises on Route Redistribution
  115. Route Redistribution for RIP
  116. Route Redistribution for EIGRP
  117. Route Redistribution for OSPF
  118. Redistribution between EIGRP and OSPF
  119. Redistribution between RIP and EIGRP
  120. Exercises on MPLS
  121. Configuring a Router for MPLS Forwarding and verifying the configuration of MPLS orwarding.
  122. Enabling MPLS
  123. Configuring MPLS LDP
  124. Configuring MPLS using EIGRP
  125. Configuring MPLS using OSPF
  126. Configuring MPLS using RIP
  127. MPLS show commands
  128. Cisco Switch IOS
  129. Introduction to Switch
  130. Switch 2960S Console Password Assignment
  131. Switch 2960S VTY Password Assignment
  132. Switch 2960S – Setting Privileged password
  133. Enable Fast Ethernet Interface on a 2960S Switch
  134. Initial Switch Configuration
  135. Basic Switch Interface Configuration
  136. Catalyst 2960S Switch Configuration
  137. Exercises on Spanning Tree Protocol
  138. Enabling STP
  139. Configuring Root Switch
  140. Configuring Port-Priority
  141. Configuring Switch Priority of a VLAN
  142. Configuring STP Timers
  143. Verifying STP
  144. Exercises on Switch Configuration and VLAN
  145. Basic Switch IP Configuration
  146. Configuring 2960S Switch vlan
  147. Troubleshooting 2960S Switch
  148. 2960S Trunking Configuration
  149. Creating and Deleting 2960S VLAN's
  150. Configuring VTP on 2960S Switch
  151. Configuring VTP with a VTP Client
  152. Troubleshooting lab with non matching domains
  153. Troubleshooting lab with trunk functionality
  154. VLANs Scenario
  155. VTP Scenario
  156. VLANs and Trunking
  157. Routing between VLANs
You may visit the site and download free trail of the software CCNA Netsim. Available commands may be viewed by going to CCNA Commands page.

Comments

Post a Comment

Popular posts from this blog

CCNA Network Simulator With Designer

Image
CCNA Network Simulator With Designer:   CertExams.com offers Network Simulator With Designer for CCNA , NetSim with Visualizer provides a virtual lab environment where a router or switch network can be simulated and also provides drag-n-drop feature for inserting devices and connectors. GUI based device configuration is provided for easy network configuration. The software is primarily intended for candidates preparing for Networking Exams such as CCNA,CCENT/ICND1 and ICND2. Several New features have been Added in the current version including Lab exercises which is Listed below. Important features of the NetSim software: Router and switch IOS simulator for ease of learning Cisco router/switch commands. S everal lab exercises with scenario type labs have been provided for hands-on practice. Connectors available are Serial, Ethernet, IsdnBri, Frame Relay, Fast Ethernet. Labs included for switches 19xx,29xx.  Labs included for Routers 25...
Read more

Certexams.com JNCIA Netsim - Designer and Virtual Simulator

Image
Certexams.com is a website that provides various certification practice exams, including for Juniper JNCIA (Juniper Networks Certified Associate) certification. The Juniper JNCIA certification is an entry-level certification that validates a candidate's knowledge and skills in networking fundamentals and Juniper Networks JUNOS software. Certexams.com offers the following features for their Juniper JNCIA practice exams: Multiple exam modes: The practice exams are available in two modes, namely, exam simulator mode and learn mode. The exam simulator mode provides a simulated environment for taking the exam, while the learn mode is designed to help candidates learn the topics covered by the exam. Question types: The practice exams include different types of questions, such as multiple-choice, true/false, and fill-in-the-blank. This provides a variety of question formats, similar to what is expected on the actual certification exam. Detailed explanations: The practice exams include det...
Read more